Open Journal Systems

Desain dan Pengembangan Prototipe Alat Uji Pembangkit Listrik Tenaga Mikro Hidro dengan Back Flow Water System

       Heri Suripto, Saiful Anwar

Abstract


Inovasi pengembangan Pembangkit Listrik Tenaga Mikro Hidro (PLTMH) terus dikembangkan mengingat kebutuhan akan energi listrik terus meningkat. Hal ini perlu didukung adanya media pembelajaran untuk mencari solusi alternatif permasalahan dalam mengatasi kebutuhan energi tersebut. Penelitian ini mendesain dan mengembangkan pembuatan PLTMH dengan back flow water system. Implementasi sistem berupa prototipe yang dapat digunakan sebagai media pembelajaran mahasiswa dan alat uji energi alternatif hidro. Metode perancangan dan manufaktur menggunakan metode Pahl & Beitz dan pengujian menggunakan metode eksperimen dengan cara pengamatan dan pencatatan data-data yang ditunjukkan pada alat ukur.  Pengujian dilakukan dua tahap, pengujian pertama pada putaran kincir dan transmisi, pengujian kedua pada putaran dinamo dan voltase. Hasil pengujian menunjukkan bahwa sistem yang dirancang memiliki unjuk kerja yang baik.


  http://dx.doi.org/10.31544/jtera.v5.i2.2020.221-230

Keywords


energi alternatif; prototipe alat uji; PLTMH back flow water system; putaran; voltase

Full Text:

  PDF

References


R. R. Singh, B. A. Kumar, D. Shruthi, R. Panda, and C. T. Raj, “Review and experimental illustrations of electronic load controller used in standalone Micro-Hydro generating plants,” Eng. Sci. Technol. an Int. J., vol. 21, no. 5, pp. 886–900, 2018.

E. B. K. Signe, B. Bogno, M. Aillerie, and O. Hamandjoda, “Performance in feasibility studies of micro hydro power plants. New software development and application cases in Cameroon,” Energy Procedia, vol. 157, pp. 1391–1403, 2019.

L. Jasa, A. Priyadi, and M. H. Purnomo, “Experimental Investigation of Micro-Hydro Waterwheel Models to Determine Optimal Efficiency,” Appl. Mech. Mater., vol. 776, pp. 413–418, 2015.

F. U. Khan, A. Ahmed, U. K. Jadoon, and F. Haider, “Modeling, Simulation and Fabrication of an Undershot Floating Waterwheel,” J. Eng. Appl. Sci., vol. 34, no. 2, pp. 55–69, 2015.

C. Vidali, S. Fontan, E. Quaranta, P. Cavagnero, and R. Revelli, “Experimental and dimensional analysis of a breastshot water wheel,” J. Hydraul. Res., vol. 54, no. 4, pp. 473–479, 2016.

N. K. Hira Singh Sachdev, Ashok Kumar Akella, “Analysis and evaluation of small hydropower plants: A bibliographical survey.,” Renew. Sustain. Energy Rev., vol. 51:1013 –, 2015.

K. Y. L. Nima Izadyar, Hwai Chyuan Ong, W.T. Chong, “Resource assessment of the renewable energy potential for a remote area: A review,” Renew. Sustain. Energy Rev., vol. 62:908 – 9.

P. A. M. C.P. Jawahar, “A review on turbines for micro hydro power plant,” . Renew. Sustain. Energy Rev., vol. 72:882 – 8, 2017.

R. Marliansyah, D. N. Putri, A. Khootama, and H. Hermansyah, “Optimization potential analysis of micro-hydro power plant (MHPP) from river with low head,” Energy Procedia, vol. 153, pp. 74–79, 2018.

A. Tapia, D. G. Reina, and P. Millán, “Optimized micro-hydro power plants layout design using messy genetic algorithms,” Expert Syst. Appl., vol. 159, p. 113539, 2020.

M. Binama, W. T. Su, X. Bin Li, F. C. Li, X. Z. Wei, and S. An, “Investigation on pump as turbine (PAT) technical aspects for micro hydropower schemes: A state-of-the-art review,” Renew. Sustain. Energy Rev., vol. 79, no. April 2016, pp. 148–179, 2017.

R. K. Saket, “Design, development and reliability evaluation of micro hydro power generation system based on municipal waste water,” 2008 IEEE Electr. Power Energy Conf. - Energy Innov., 2008.

V. Valsan and P. Kanakasabapathy, “Design and implementation of smart energy management system for stand-alone micro-hydro systems,” Proc. 2017 IEEE Int. Conf. Technol. Adv. Power Energy Explor. Energy Solut. an Intell. Power Grid, TAP Energy 2017, pp. 1–6, 2018.

F. M. Tamiri, M. A. Ismail, and W. K. Muzammil, “Low head micro hydro systems for rural electrification,” IOP Conf. Ser. Mater. Sci. Eng., vol. 834, no. 1, 2020.

L. Wei, T. Nakamura, and K. Imai, “Development and optimization of low-speed and high-efficiency permanent magnet generator for micro hydro-electrical generation system,” Renew. Energy, vol. 147, pp. 1653–1662, 2020.

J. Jamal and L. Lewi, “Utilization of irrigation flow for the construction of micro-hydro power plant,” AIP Conf. Proc., vol. 1977, 2018.

A. . C. Gunjan Yadav, “Design and Development of Pico Micro Hydro System By Using House Hold Water Supply,” Int. J. Res. Eng. Technol., vol. 03, no. 22, pp. 114–119, 2014.

A. Zaman and T. Khan, “Design of a Water Wheel For a Low Head Micro Hydropower System,” J. Basic Sci. Technol., vol. 1, no. 3, pp. 1–6, 2012.

F. Elfinurfadri, R. Rasyid, and H. Nasbey, “Pengembangan Miniatur Pembangkit Listrik Tenaga Uap Sebagai Media Pembelajaran Fisika Sekolah Menengah Atas ( SMA ),” Semin. Nas. Fis. Univ. Negeri Jakarta, pp. 129–133, 2013.

G. Pahl, W. Beitz, J. Feldhusen, and K. H. Grote, Engineering Design, Third. Springer, 2007.

I. G. A. D. Unggul Wibawa, Hari Santoso, “Perancangan kincir air pembangkit listrik tenaga mikrohidro (PLTMH) desa bendosari kecamatan pujon kabupaten malang,” J. Elektro Vol. 7 No. 1 Juli 2014, vol. 1, no. 1, pp. 1–14, 2014.

Wariito, D. Adanta, S. A. Arifianto, S. B. Nasution, and Budiarso, “Effect of Blades Number on Undershot Waterwheel Performance with Variable Inlet Velocity,” Proc. - 2018 4th Int. Conf. Sci. Technol. ICST 2018, no. 4749, pp. 1–6, 2018.

E. Quaranta and R. Revelli, “Gravity water wheels as a micro hydropower energy source: A review based on historic data, design methods, efficiencies and modern optimizations,” Renew. Sustain. Energy Rev., vol. 97, no. November 2017, pp. 414–427, 2018.

H. Suripto et al., “Analisis Kecepatan Masuk Sudut Runner Turbin Cross flow dengan Simulasi CFD,” no. 1, pp. 39–44, 1949.

H. Suripto and S. Anwar, “Optimasi Perancangan Turbin Crossflow Terhadap Sudut Masuk Blade Runner Untuk Micro Hydro Power Plant Dengan Analisis Cfd,” Rotasi, vol. 22, no. 1, pp. 48–54, 2020.

R. Effendi and M. Khumaidi, “Perancangan Mesin Perajang Bawang Serbaguna Berpenggerak Motor Listrik Dengan Kapasitas 55 Kg/Jam,” J. POLIMESIN, vol. 16, no. 2, p. 47, 2018.




DOI: http://dx.doi.org/10.31544/jtera.v5.i2.2020.221-230
Abstract 305 View    PDF viewed = 132 View

Refbacks

  • There are currently no refbacks.


Copyright (c) 2020 JTERA (Jurnal Teknologi Rekayasa)

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Copyright @2016-2021 JTERA (Jurnal Teknologi Rekayasa) p-ISSN 2548-737X e-ISSN 2548-8678.

     Lisensi Creative Commons

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

 

JTERA Editorial Office:
Politeknik Sukabumi
Jl. Babakan Sirna 25, Sukabumi 43132, West Java, Indonesia
Phone/Fax: +62 266215417
Whatsapp: +62 81809214709
Website: https://jtera.polteksmi.ac.id
E-mail: jtera@polteksmi.ac.id